CODA Audio LiNUS6.4-i DSP amp 4x1500W, Flex bridge pair CODA Audio LiNUS6.4-i DSP amp 4x1500W, Flex bridge pair CODA Audio LiNUS6.4-i DSP amp 4x1500W, Flex bridge pair CODA Audio LiNUS6.4-i DSP amp 4x1500W, Flex bridge pair

CODA Audio LiNUS6.4-i DSP amp

4x1500W, Flex bridge pair

Varenr: LiNUS6.4-i
36 119,-eks mva.
Logg inn for å se dine nettopriser.
Ikke kunde? Søk om kundestatus.
9 På lager
BeskrivelseTeknisk infoAlternativerDokumenter
Beskrivelse

LINUS6.4 :

4 Channel Installation DSP Amplifier with Loudspeaker Management

Integrated DSP, 6000 W @ 2Ω, 4 channel networkable installation amplifier

19"/1U Four channel amplifier for fixed installations, delivers 4x 1500 W @ 2Ω or 2x 3000 W@ 4Ω or 1x 3000 W@ 4Ω + 2x 1500 W@ 2Ω, controlled via the front panel, LINUS App or LINUS Control.

 

OVERVIEW

The LINUS6.4 is a four-channel DSP networkable installation amplifier delivering 4 x 1500 W of clean power in a convenient and lightweight 19”/1U package. 

Advanced Class D discrete power stages with DC-coupled DACs, together with a high-efficiency SMPS with PFC to provide unrivalled power density and minimal thermal dissipation. 

The innovative PCB layout design integrates DSP, four amplifiers, and SMPS on a single PCB for enhanced sound quality, pinpoint control, and rugged protection. 

The four audio inputs are selectable, you can choose between analog, LiNET, Dante digital audio network and simply and easily route to any of the four outputs via the input matrix.

The advanced DSP processor enables the integration of sophisticated audio algorithms including phase linear DS-FIR filters, these provide perfect linearity and superior sound performance, plus advanced look-ahead and frequency-dependent limiters. The end result is increased system headroom and sonic fidelity, even under heavy use conditions.

 

Main Features

  • 4x 1500 W @ 2Ω or 2x 3000 W@ 4Ω or 1x 3000 W@ 4Ω + 2x 1500 W@ 2Ω
  • Powers either 70/100V and low impedance loudspeakers
  • 4 balanced analogue inputs
  • LiNET – 8x freely configurable digital audio signals over CAT5e
  • Dante redundant (LINUS 6.4-iD only)
  • PoE on the control port, in case of mains power loss, the control section still functions
  • Phoenix inputs and outputs
  • Configurable GPIO
  • Front panel IPS display (240×240 pixels) 
  • Front panel control
  • LINUS Control – full network control and monitoring of amplifiers over Ethernet
  • LINUS App – full amplifier control and monitoring via mobile device using internal wi-fi hotspot
  • Optimised factory presets for all CODA Audio loudspeaker systems
    (except N-RAY, ViRAY, CiRAY, AiRAY, and sensor subwoofers)
  • 5-year warranty
Teknisk info

Produktinformasjon

AC mains frequency 47 – 63 Hz
AC mains input connector EURONET C14
AC mains voltage
  • 265 V = Maximum
  • 90 V = Minimum
  • Amplifier ¼ power = 1700 W
Analogue input impedance 44 kOhm
Cooling System
  • 2x thermally controlled fans
  • Hot air expelled at rear
Damping Factor 8 Ohm load, 1 kHz & below 2500
Ethernet connection 1 x 100 Mbps RJ45 Control
Farge Sort
Frequency response 20 Hz – 20 kHz = (+0.0 dB /-1.0 dB)
Input connections
  • 1X RJ45 LINET IN (8x CH)
  • 1x RJ45 LINET LINK (8x CH)
  • 4x PHOENIX 3P Analog IN
Input sources
  • Analog
  • LiNET
Internal samplerate / bit-depth 48 kHz / 32 bit
LED indicators
  • Ethernet connected / IP address
  • Limit
  • Mute status
  • Power on / Limiting
  • Protection
  • Signal
Maximum input level +21 dBu / 8.7 Vrms
Maximum output current +/- 50 A pk
Maximum output voltage
  • +/- 180 V pk (BTL)
  • +/- 90 V pk (SE)
Minimum output load
  • 2 Ohm nom SE
  • 4 Ohm nom BTL
Number of output channels 4
Operating temperature
  • +5°C to +55°C
  • 41°F to 131°F
Output stage Class D
Peak output power 6 dB Crest Factor
  • 1000 W pk @ 8 Ohm SE
  • 1500 W pk @ 4 Ohm SE
  • 3000 W pk @ 2 Ohm SE
Power consumption
  • Amplifier ¼ power = 1700 W
  • Amplifier idle <= 25 W
  • Amplifier in standby <= 15 W
Power output connections 2x PHOENIX 4P
Protection circuits
  • Inrush current limiter
  • Output DC
  • Output overload
  • SMPS over-current
  • Thermal limiter
RMS output power THD <0.01%
  • 1x 3000 W @ 4 Ohm + 2x 1500 W @ 2 Ohm
  • 2x 3000 W @ 4 Ohm
  • 4x 1500 W @ 2 Ohm
Supported digital input formats
  • 176.4 kHz
  • 192 kHz
  • 32 kHz
  • 44.1 kHz
  • 48 kHz
  • 88.2 kHz
  • 96 kHz
Thermal output
  • 0.025 = Idle
  • 0.205 = 20 %
  • 0.475 = 50 %
  • 0.925 = 100 %
Thermal output (BTU/h)
  • 1621 = 50 %
  • 3156 = 100 %
  • 700 = 20 %
  • 85.3 = Idle
Type u/Dante


Alternativer
Dokumenter

 


SIST SETTE PRODUKTER


48935